Service & Maintenance / Extra Edition

Btu Buddy 70: Smoking Gas Package Unit

January 19, 2009
/ Print / Reprints /
ShareMore
/ Text Size+

Bob is a service technician who is well trained and nationally certified. However, he sometimes suffers from the same confusion that all technicians occasionally do - the facts that he gathers may or may not point to the obvious cause of the problem or the best solution. But Bob has something that no one else has. He recalls his long-time HVACR mentor and imagines him accompanying him as “Btu Buddy,” someone who reminds him to take time to stop and think before rushing to judgment, helping keep him on the right track, even with facts that are confusing.

Figure 1. This is a typical gas package unit. (Figure is from Refrigeration & Air Conditioning Technology, 5th Edition, by William Whitman, William Johnson, and John Tomczyk, published by Delmar Cengage Learning.) (Click on the image for an enlarged view.)

Bob got a call about a new customer who complained about their gas package unit smoking and smelling bad (Figure 1). Bob called the customer who explained that the unit could be smelled at the street about 60 feet away when the wind was blowing in that direction. The customer also said that smoke was coming out of the unit’s vent. Bob advised the customer to shut the unit off until he could get there. He explained that there should not be any fumes entering the house, but to be safe, turn it off.

When Bob arrived, he talked to the customer and then turned the unit off at the disconnect switch at the unit. He then went inside and turned the thermostat up to call for heat. He then went outside to the unit and started it with the disconnect switch. Sure enough, a light black smoke was coming out of the vent. Bob removed the burner compartment panel and looked at the flame and it didn’t look all that bad. He was scratching his head when Btu Buddy showed up.

Btu Buddy asked, “What is the problem, Bob?”

Bob said, “I have never seen a gas appliance smoke like this, and it really smells bad.”

Btu Buddy then asked, “What would cause a gas flame to smoke?”

Bob said, “Maybe too much fuel, or not enough air. The vent seems to be working and I can hear the vent fan turning, so it must be good. Maybe there is too much pressure on the gas manifold causing too much gas for the amount of combustion air.”

Btu Buddy then said, “Why don’t you take off the vent cover and see if there could be a blockage at the fan outlet?”

Bob removed the cover and took a light and looked inside and said, “Here is the problem. The fan wheel is all torn up. I don’t see how it could move any air, but something is moving the air.”

Bob removed the fan and wheel and looked it over. He then said, “I don’t see how that worked at all. There is no sign of the rest of the fan wheel. I wonder where it went. I think I need to talk to the customer and see if she knows anything.”

Bob talked to the customer and the customer said, “We had problems with this unit last spring, just at the end of the heating season. The contractor is no longer in business. The contractor told me that the heat exchanger had a hole in it and changed it out in warranty. It only cost us for the labor. He didn’t mention what could have caused it.”

Figure 2. This is a motor and fan assembly similar to the one that Bob replaced. (Figure is from Practical Heating Technology by William Johnson, published by Delmar Cengage Learning.) (Click on the image for an enlarged view.)

Bob showed her the fan wheel and she wanted to know what it should look like, so Bob showed her a picture of a new motor and fan wheel (Figure 2). He explained to her that there was no sign of the rest of the wheel.

She told Bob to make the repair.

Bob was making the repair when Btu Buddy suggested, “I think the contractor last year found the defective fan wheel when he installed the heat exchanger and just threw the missing pieces away and didn’t mention it. It was going to cost even more, so he just didn’t do his job because he didn’t want to go back to the customer for more money than his estimate. He must have noticed that the vent smelled bad, but assumed it was venting good enough. Probably the old fan wheel was what caused the heat exchanger to fail. If the unit had operated for long, the heat exchanger would have failed again and then the customer would have really been mad.”

Bob decided to see if he could change just the fan wheel and tried to remove it from the fan motor shaft. Then he discovered the hex head nut holding the fan wheel on the shaft was rusted out inside and an Allen wrench would not get a grip to turn it. He then said to Btu Buddy, “I am going to have to change the motor and the fan wheel - even more expense.”

Bob went to the supply house with the old motor and fan wheel where the counter man said, “You are doing the right thing. I have noticed that nobody can remove these old fan wheels from the shaft because of the rusty Allen screw.”

Bob had the new fan assembly and went back to the job to install it.

Btu Buddy said to Bob, “Shine your flashlight into the heat exchanger at the top where the fan mounts and at the bottom where the burners are and look closely for signs of soot deposits.”

Bob used his light and examined the heat exchanger from both ends and said, “There are no signs of soot. We are good to go forward.”

Btu Buddy then said, “Thank goodness the homeowner got right on this, before it had enough running time to accumulate soot.”

Bob asked Btu Buddy, “Why was there so much rust in the fan section?”

Btu Buddy explained, “The unit is about 11 years old. Every time it starts up, it gets a blast of moist air from combustion and that air is slightly caustic, about like a soft drink. After years of exposure, it just accumulates rust. I have never seen one that is rusted out like this one. Notice, the new fan wheel is coated with a galvanized zinc coating. The original one should have been coated the same way. It is possible that it did not get a good thick coat of galvanizing for proper protection.”

Bob then asked a crucial question, “How come combustion was allowed to keep going when there was not enough airflow? It seems like it should have shut the unit down.”

Btu Buddy then said, “Let me start by saying, there are three methods of proving airflow in a forced combustion system:

1. Some systems have a pressure switch across the blower that proves airflow.

2. Some systems have a “sail switch” that moves to make a set of contacts to verify combustion.

3. Some combustion motors have an “end switch” built into the motor to assure the combustion fan is turning. This assumes that the fan will move air when the motor is turning.

All of these systems open the gas valve when airflow is established. I guess your vote would be for either number 1 or 2, after today’s experience.”

Bob said, “Yes, this system sure didn’t function as expected. Who would have expected a fan wheel to completely come apart? It seems like it would have made a noise.”

Btu Buddy said, “The last technician did not do a professional job. You know better than to leave a job like this when it still had problems.”

Publication date: 01/19/2009

Did you enjoy this article? Click here to subscribe to The NEWS Magazine

Recent Articles by Bill Johnson

You must login or register in order to post a comment.

Multimedia

Videos

Image Galleries

2014 MCAA Annual Convention

Scenes from the 2014 MCAA Annual Convention in Scottsdale, Ariz.

Podcasts

NEWSmakers: Julian Scadden

Training is an ongoing process. Julian will discuss how you can generate maximum return on time and energy invested training by following a three part process. Listen to this podcast to get expert tips on training, tracking and follow up. 

More Podcasts

THE MAGAZINE

ACHRNEWS

NEWS 04-14-14 cover

2014 April 14

Check out the weekly edition of The NEWS today!

Table Of Contents Subscribe

SERVICE CALLS POLL

Which statement on service calls best applies to your business?
View Results Poll Archive

HVACR INDUSTRY STORE

plumbing-hvac.gif
2014 National Plumbing & HVAC Estimator

Every plumbing and HVAC estimator can use the cost estimates in this practical manual!

More Products

Clear Seas Research

 

Clear Seas ResearchWith access to over one million professionals and more than 60 industry-specific publications, Clear Seas Research offers relevant insights from those who know your industry best. Let us customize a market research solution that exceeds your marketing goals.

DON'T MISS A THING

Magazine image
 
Register today for complete access to ACHRNews.com. Get full access to the latest features, Extra Edition, and more.

STAY CONNECTED

facebook icontwitter iconyoutube iconLinkedIn i con