Make Sure Your Vacuum Pump Measures Up

October 29, 2004
/ Print / Reprints /
ShareMore
/ Text Size+
Service technicians need to completely evacuate a refrigeration system any time they open the system to the atmosphere. Vacuum pumps and micron gauges are the tools you need to use for this. Are yours in good working order?

System evacuation is just good service common sense. You need to remove any water vapor, nitrogen, and oxygen contained in the air before you can add refrigerant. If you leave air in the system, it will collect in the condenser, taking up space and causing the high-side pressure to be higher than normal.

Any water vapor contained in the air may freeze and cause a restriction, normally at the outlet of the metering device. Also, the water vapor and oxygen can mix and, if sufficiently heated, may create acids in the system.

Completely evacuating the system using a good-quality vacuum pump and micron gauge can prevent this from occurring. Many refrigeration manufacturers recommend evacuating a system to a 500-micron level. This normally ensures that the system is completely degassed and dehydrated.

Figure 1. The valve between the micron gauge and the vacuum pump allows a technician to perform a standing vacuum test.

Tool Maintenance

Like many service tools, vacuum pumps and micron gauges need to be maintained on a regular basis. Without regular maintenance these devices can fail - per Murphy's Law, usually when they are needed most.

Vacuum pumps should have their oil changed on a regular basis according to the manufacturer's recommendation. The sensors used in many micron gauges may need to be cleaned.

Again, always follow the manufacturer's recommended procedures for cleaning these sensors. Many manufacturers recommend cleaning the sensors with alcohol. This can be done by adding a few drops to the 1/4-inch flare connection, then gently shaking the unit and letting it air dry.

Along with regular maintenance, a technician should always check the operation of both vacuum pump and micron gauge before using them on a system. It's better to discover a problem with either of these devices before you use them on a system and potentially waste time on the job.

When you are setting up the vacuum pump and micron gauge, make sure there is a valve installed between the system and the vacuum pump/micron gauge setup. Normally you can use the refrigeration manifold gauges for this purpose.

There should also be a valve between the micron gauge and the vacuum pump (Figure 1). This allows a technician to perform a standing vacuum test on the system once a 500-micron level is achieved.

Pump Test

Following this simple test procedure can save you a lot of time. If there were a problem with the vacuum pump, you could be running a vacuum and not properly evacuating the system. If there were a problem with the micron gauge, you could be running the vacuum pump longer than may be necessary to achieve a properly evacuated system. To test the pump, do the following:

Before you open the vacuum pump and micron gauge to the system, shut the valve between the system and the vacuum pump/micron gauge setup and run the vacuum pump. This will only pull a vacuum on the vacuum hose and micron gauge.

The micron gauge should register a 500-micron level in a relatively short amount of time. If it doesn't, there is a problem with the micron gauge, vacuum pump, or interconnecting hose. You need to identify which of these devices is causing the problem and fix it before opening the vacuum pump to the system.

Joe Marchese is the owner of Coldtronics, Pittsburgh. He may be reached at 412-734-4433, www.coldtronics.com, or joe@rhvactools.com.

Publication date: 11/01/2004

Did you enjoy this article? Click here to subscribe to The NEWS Magazine

You must login or register in order to post a comment.

Multimedia

Videos

Image Galleries

2014 MCAA Annual Convention

Scenes from the 2014 MCAA Annual Convention in Scottsdale, Ariz.

Podcasts

NEWSmakers: Julian Scadden

Training is an ongoing process. Julian will discuss how you can generate maximum return on time and energy invested training by following a three part process. Listen to this podcast to get expert tips on training, tracking and follow up. 

More Podcasts

ACHRNEWS

NEWS 04-21-14 cover

2014 April 21

Check out the weekly edition of The NEWS today!

Table Of Contents Subscribe

SERVICE CALLS POLL

Which statement on service calls best applies to your business?
View Results Poll Archive

HVACR INDUSTRY STORE

plumbing-hvac.gif
2014 National Plumbing & HVAC Estimator

Every plumbing and HVAC estimator can use the cost estimates in this practical manual!

More Products

Clear Seas Research

 

Clear Seas ResearchWith access to over one million professionals and more than 60 industry-specific publications, Clear Seas Research offers relevant insights from those who know your industry best. Let us customize a market research solution that exceeds your marketing goals.

DON'T MISS A THING

Magazine image
 
Register today for complete access to ACHRNews.com. Get full access to the latest features, Extra Edition, and more.

STAY CONNECTED

facebook icontwitter iconyoutube iconLinkedIn i con