What Does That Analyzer Do, Anyway?

January 23, 2006
/ Print / Reprints /
ShareMore
/ Text Size+
Visual inspection of the flame will not always show telltale signs of CO; if a combustion analysis is not performed, the results could be severe.
When using an analyzer, it is important to understand what you are measuring and what you are calculating. Most analyzers only measure three to four parameters; the rest are calculated values.

Measured values are usually:

  • CO (carbon monoxide) - Dangerous byproduct produced by incomplete combustion.

    Stack temperature (gross stack temperature) - Temperature of the flue gasses + combustion air temperature.

  • O2 (oxygen) - Measured oxygen in flue gasses after combustion has occurred.

  • NO (nitric oxide) - Byproduct of combustion that includes mononitrogen monoxide and nitrogen monoxide.

    Calculated values include:

  • EFF (efficiency) -Calculation of the maximum heat available in the combustion process minus the stack losses.

  • NOx (nitric oxide) - The mixture includes nitric oxide (NO), nitrogen dioxide (NO2), nitrogen trioxide (N2O3), nitrogen tetroxide (N2O4), and nitrogen pentoxide (N2O5).

  • CO2 (carbon dioxide) - A byproduct of normal combustion, considered a greenhouse gas.

  • Excess air - The calculated air that passed through the combustion process without acting as an oxidizer in the combustion process. A certain amount is usually required to ensure complete combustion. Excess air dilutes the flue gasses and should be kept to a minimum to keep combustion efficiency at its maximum.

  • CO AF - A calculated measure of undiluted CO in the flue gasses.

  • Dewpoint - A calculated temperature below which the H2O in flue gas will start to condense.

    Combustion analyzers that do not contain NOx filters will cause false high CO readings. Depending on the level of NOx in the flue gas, these readings can be easily 50 ppm higher than the levels actually are, leaving the technician chasing a problem that doesn’t exist.

    PERFORMING A COMBUSTION ANALYSIS

    In general, when performing a combustion analysis, the service technician needs to look at three things:

    1. Safety.

    2. Efficiency.

    3. Production of pollutants.

    The service technician can rely on the analyzer to perform the calculations needed to determine if the combustion process is efficient, but they must also understand how each of the variables in the combustion process affect safety and appliance efficiency.

    Safety: Carbon monoxide (CO) is a pollutant that is readily absorbed in the body and can impair the oxygen-carrying capacity of the blood (hemoglobin). Impairment of the body's hemoglobin results in less oxygen to the brain, heart, and tissues. Even short-term overexposure to CO can be critical, or fatal, to people with heart and lung diseases, the young, or the elderly. It may also cause headaches and dizziness and other significant medical problems in healthy people.

    During combustion, carbon in the fuel oxidizes through a series of reactions to form carbon dioxide (CO2). However, 100-percent conversion of carbon to CO2 is rarely achieved under field conditions; some carbon only oxidizes to the intermediate step, CO.

    Efficiency: Older furnaces and boilers generally have higher levels of CO than new equipment because older burners were not designed to achieve low CO levels. In today's equipment, high levels of CO emissions primarily result from incomplete combustion due to poor burner design or firing conditions (for example, improper air-to-fuel ratio) or possibly a misaligned burner.

    Through proper burner maintenance, inspections, operation, or by upgrading equipment and performing regular inspections (including combustion testing), the formation of carbon monoxide can be limited to an acceptable level.

    Pollutants: No standards for CO have been agreed upon for indoor air. The U.S. National Ambient Air Quality Standards for outdoor air are 9 ppm (40,000 micrograms per meter cubed) for 8 hours, and 35 ppm for 1 hour.

    No CO (0 ppm) is the best level in the home. This cannot always be achieved due to smokers in the home and/or appliances, like stoves, that are producing acceptable levels of CO during operation. Whenever CO is measurable, the source should be determined and corrective action determined to ensure occupants' safety and minimize the exposure.

    The local jurisdiction should be consulted when determining the maximum safe level allowed in the home before shutting down the appliance and/or making it inoperable. An appliance with rising CO production should always be shut down no matter how low CO production is at the time of testing. Rising CO problems are usually the result of improper venting and/or lack of combustion air.

    Liners should be inspected yearly. This liner was the victim of an incorrect installation that caused premature failure. A properly installed liner will last for the life of the appliance.

    LIGHT-OFF CO LEVELS

    "Light-off" levels of CO have been addressed as an area of concern by many people in industry. Gas and oil appliances have no prescribed maximum CO level at light off. High CO levels at light off may be an indication of rough or delayed ignition warranting further investigation, but they are not considered by manufacturers to pose health concerns due to the short time of higher concentration.

    The CO readings should peak at less than 400 ppm (there are no prescribed light-off levels), then drop below the prescribed level allowed in the stack. CO readings should stabilize within 10 minutes of operation and should never be rising during operation.

    Technicians and manufacturers should be aware that many manufacturers of combustion testing equipment do not filter out the NOx from the combustion sample. NOx can be cross-referenced as CO if not filtered. (Testo analyzers incorporate NOx filters that remove NOx from the CO sample to provide an accurate CO reading.)

    If you are using an analyzer that does not filter NOx, be aware that what appears to be unacceptable CO levels may be well within an acceptable range. This is an issue that affects consumers, technicians, and manufacturers alike. Accurate analysis of the fuel gasses is imperative to making proper combustion analysis.

    Sidebar: Limits And Levels

    AMBIENT CO LIMITS

  • 1-9 ppm: Normal levels within the home. If there are no smokers, investigation is recommended.

  • 10-35 ppm: Advise occupants, check for symptoms, check all unvented appliances, and furnace, how water tank and/or boiler.

  • 36-99 ppm: Recommend fresh air, check for symptoms, ventilate the space, and recommend medical attention.

  • 100-plus ppm: Evacuate the home and contact emergency medical services (911). Don't attempt to ventilate the space. Short-term exposure to these levels can cause damage.

    MAXIMUM EQUIPMENT LEVELS
    Vented (CO reading must remain stable):

  • 400 ppm stack ANSI.
  • 100 ppm stack recommended.

    Unvented (CO reading must remain stable):

  • 30-50 ppm stable.
  • Less than 10 ppm recommended.

    Publication date: 01/23/2006

  • Did you enjoy this article? Click here to subscribe to The NEWS Magazine

    You must login or register in order to post a comment.

    Multimedia

    Videos

    Image Galleries

    2014 MCAA Annual Convention

    Scenes from the 2014 MCAA Annual Convention in Scottsdale, Ariz.

    Podcasts

    NEWSmakers: Julian Scadden

    Training is an ongoing process. Julian will discuss how you can generate maximum return on time and energy invested training by following a three part process. Listen to this podcast to get expert tips on training, tracking and follow up. 

    More Podcasts

    THE MAGAZINE

    ACHRNEWS

    NEWS 04-14-14 cover

    2014 April 14

    Check out the weekly edition of The NEWS today!

    Table Of Contents Subscribe

    SERVICE CALLS POLL

    Which statement on service calls best applies to your business?
    View Results Poll Archive

    HVACR INDUSTRY STORE

    plumbing-hvac.gif
    2014 National Plumbing & HVAC Estimator

    Every plumbing and HVAC estimator can use the cost estimates in this practical manual!

    More Products

    Clear Seas Research

     

    Clear Seas ResearchWith access to over one million professionals and more than 60 industry-specific publications, Clear Seas Research offers relevant insights from those who know your industry best. Let us customize a market research solution that exceeds your marketing goals.

    DON'T MISS A THING

    Magazine image
     
    Register today for complete access to ACHRNews.com. Get full access to the latest features, Extra Edition, and more.

    STAY CONNECTED

    facebook icontwitter iconyoutube iconLinkedIn i con