Service & Maintenance / Extra Edition

Screw Compressor Teardown: A Few Basics - Part 2

March 6, 2003
/ Print / Reprints /
ShareMore
/ Text Size+
Editor’s Note: This is the second installment of a two-part series.

Part One of this article provided some background on screw compressors, then discussed the various components and capacity control methods. Part Two discusses maintenance of the screw compressor.

Maintenance

To ensure a full operating life from a compressor, preventive maintenance is absolutely essential. Because the compressor is mounted on a unit, operating conditions of the unit play a major role in the life of the compressor. Below is a list of preventive maintenance items dealing both with the compressor and the unit. First and foremost, always follow the manufacturer’s recommended maintenance schedule. However, the following recommendations can be applied to most systems.

Operating Logs

Recording the operating conditions every four hours or at least once per shift permits those responsible for the maintenance and servicing of the equipment to be constantly familiar with the operation of the system. Any deviation from the normal operating conditions is easily recognized and immediate steps can be made to correct the problem. A few typical areas to look for would be high or low discharge temperature, high or low oil temperature, low oil pressure, and high full load amp percentage.

Discharge Temperature

Lower than normal discharge temperatures could indicate liquid refrigerant carry-over or excessive liquid injection feed.

Higher than normal discharge temperatures could indicate an incorrect Vi (volume ratio) position, insufficient main oil supply, excessive suction line superheat, or an increase in the rotor end clearance.

Oil Temperature

Excessively high oil temperature can adversely affect the oil’s ability to supply proper lubrication.

If the oil temperature is too low, refrigerant may become entrained in the oil supply and enter into the bearing cavities.

An increase in full load amps while maintaining the same operating conditions could indicate a faulty bearing.

Rotor Thrust Measurement

Measuring the axial movement of the rotor can help determine the condition of the thrust bearing. By moving the rotor axially back and forth, and comparing that measurement with the “as built” measurement, excessive thrust bearing movement can be detected. Obviously, the drive rotor is easy to measure as it protrudes from the compressor; however, access to the non-drive rotor will require some disassembly of the compressor.

For compressors with anti-friction roller bearings for radial loads, clearance measurements can only be taken with a feeler gauge between the inner race and the top roller element. Do not pry the rotor up and down. Excessive radial movement of the rotor shaft could result in damage to the bearings.

Oil Analysis

The use of the correct oil in a compressor is essential for long-term operation. Ensuring that the oil quality is in line with the manufacturer’s recommendations is equally important. Conducting oil analyses in scheduled intervals allows the operator to know the condition of the oil and when it is time to change the oil. An oil analysis should look for viscosity, moisture, wear metals, particle count, and on certain refrigerants, total acid number. Consult the compressor manufacturer for testing lab recommendations. It is important to have a testing laboratory that is knowledgeable about refrigeration oils.

Vibration Analysis

Vibration analysis is a highly accurate and effective method to monitor the condition of anti-friction bearings. A quality vibration program, monitoring compressors with anti-friction bearings, can give advance warning of bearing defects long before a complete failure. Vibration analysis can also eliminate the need for periodic teardown inspections that are typically based on hours. It is important that the person taking the readings is familiar with the bearings and the operation of the compressor.

Being Familiar With The Compressor

Not all companies can financially afford the benefits of oil or vibration analysis programs. In this case, a trained operator can become familiar with their compressor to the point that changes in sound levels and pitches can alert them to a problem.

Remember that preventive maintenance is proactive and can save both time and money.

Servicing

Minor repair: This is usually defined as work performed on the compressor while it’s still mounted on the unit. Typical minor repair items would consist of replacing the slide valve and slide stop potentiometers, slide valve piston seal ring, and miscellaneous O-rings. High on the list of minor repairs would be replacing the shaft seal. Compressor manufacturers attempt to install reliable and durable shaft seals; however, the most durable shaft seal will have to be replaced eventually. A shaft seal, like bearings, is designed with a particular compressor and application in mind. It is important to consult the compressor manufacturer for the correct shaft seal.

Major repair categories: Major repair to compressors can usually be broken down into three categories. The first would be replacing bearings, O-rings, and fasteners. This type of repair is often associated with hours of operation rather than a known problem. Some manufacturers recommend this type of repair as a scheduled maintenance item. However, since the onset of vibration analysis, many end users now rely on vibration measurements to predict the need for rebuilding rather then operating hours. As discussed earlier, vibration analysis can often detect a problem before it is audible to the human ear.

The second category would be bearings, O-rings, and a few internal components. Again, this could be based on hours of operation and vibration readings as well as audible noise or compressor performance. Replaceable items could be balance pistons, slide valve, and slide stop.

The third category would include the first two groups as well as additional major components. Items such as rotors and major housings would be required as a result of a compressor failure. Compressors falling into this category will need to be evaluated to determine if rebuilding is a more financially advantageous decision than purchasing a replacement compressor.

Dismantling

Discussion on compressor dismantling is somewhat difficult due to the scores of different compressor designs on the market. No matter which design is being dismantled, a few basic steps and procedures should be followed.

  • Have the right work area. Dismantling and rebuilding should be conducted in a clean environment free of airborne particles. Due to the weights of rotors and housings, an overhead lifting device is required.

  • Use the proper tools. Because screw compressors have close tolerance clearances and precision components, most compressors require special tools designed by the manufacturer to remove and install bearings, locknuts, springs, etc. The use of these tools is critical to ensure that components are installed in a quality manner. The tools also allow the technician to work safely.

  • Know what is inside the compressor. Some compressors have high-pressure springs as part of their design. Unknowingly removing a cover could launch the cover and the spring causing injury to the technician.

    Be sure you know what is inside the compressor.


    Assembly

  • Conduct a full rebuild. A common mistake in compressor rebuilding is conducting a partial rebuild. A partial rebuild would consist of replacing only one or two of the bearings rather than all the bearings, or not replacing all the seal rings in the slide valve assembly. Although units have oil filters to protect the compressor, the oil porting in the compressor allows the oil to flow from one bearing to another. If the upstream bearing is worn, the downstream bearing will become contaminated.

  • Use factory approved parts. Because of the critical design specifications and the particular application the compressor is used for, manufacturers use specific parts for specific compressors. For instance, o-ring material depends upon the refrigerant being used. The use of incorrect o-rings could result in the o-ring becoming hard, swollen, soft, or other types of deformities. The end result will be gas and oil leakage, and possibly excessive difficulty in dismantling.

    Other critical items are bearings. Bearings are designed to handle specific loads, speeds, and conditions. Although the bearing manufacturer has a generic identification on their bearings, the identification may not always specify the exact bearing design. An example of this may be that the bearing clearance is not specified on the bearing code. As mentioned previously, it is strongly recommended to use the manufacturer’s designed shaft seal.

    Once the correct seal is obtained, a few basic pre-installation techniques are recommended.

    1. Ensure all compressor components are cleaned and ready for re-installation before removing the shaft seal from its package.

    2. Once the seal is removed from the package, care must be taken to avoid contamination.

    3. Never attempt to wipe the seal faces with anything other than a clean alcohol swab. Seal faces are lapped to two to three helium light bands. One helium light band is 11.6 millionths of an inch. Rubbing the faces with some other cloth may result in scratching the face.

    4. The majority of shaft seals require coating the surfaces with oil prior to installation. Never wipe on the oil with a cloth or brush as both may either scratch the carbon or leave contaminants. The seal can be lubricated by either dipping the seal in clean refrigeration oil or by using a spray bottle.

    5. Never use grease or products such as STP for either installation or lubrication. These products have a higher viscosity than refrigeration oil and may cause premature failure due to sludge formation.

    Most shaft seals have an allowable oil leak rate; check with the manufacturer for the maximum allowable rate. Below is a list of possible causes for excessive shaft seal leakage.

  • Misalignment between the compressor and motor.

  • Improper or inadequate oil.

  • Poor oil filtration.

  • Incorrect shaft seal for the application.

  • Incorrect o-ring material.

  • Damage to an o-ring.

  • Excessive axial and/or radial movement of the shaft.

  • Improper installation.

    Failure Analysis

    Another important aspect in compressor rebuilding is to determine the cause of failure by analyzing the failed components. The most common mistake during a teardown evaluation is concentrating on the damage that occurred rather than what caused the damage. To get a better understanding of what to look for, the following is a list of possible failure modes.

  • Inadequate lubrication:
    Perhaps the leading cause for compressor failures can be attributed to lubrication-related problems. Poor lubrication will cause the bearings to fail. Although it could be described as a bearing failure, it would actually be a lubrication failure. Partial lists of items that contribute to a lubrication failure are listed below:

    1. Using the wrong type of oil.

    2. Contaminants such as moisture, particles, or liquid refrigerant.

    3. Mixing different types of oils.

  • Bearing failure:
    Again, it has to be determined what caused the bearing to fail in order to determine what caused the compressor to fail. To determine a bearing failure, it is best to evaluate all the bearings. A partial list of bearing failure modes is shown below.

    1. Failure due to defective bearing seats on shaft and in housings: For the bearing to achieve its life expectancy, it’s essential that the shaft and the housing be geometrically true with the bearing.

    2. Misalignment: Misalignment can occur between the compressor and motor or it can occur if the inner ring is seated against a shaft shoulder that is not square.

    3. Faulty mounting practice: Failures under this item occur from abuse or neglect of the bearing before and during mounting. Besides mechanical damage as a result of abuse, allowing the bearing to become contaminated will result in a premature failure.

    4. Damage due to improper fit: This occurs when the wrong bearing design is used. This typically occurs when deviating from the manufacturer’s specified bearing.

    5. Inadequate or unsuitable lubrication: This occurs when using the wrong specification of oil or poor quality oil.

    6. Vibration: A unit that is vibrating excessively during operation will result in premature bearing failures. Another type of vibration-related failure is called false brinelling. False brinelling occurs when the compressor is off for an extended period of time without the rotor shafts being rotated while a nearby machine is running. Micro-motion occurs between the rolling elements and inner raceway that will eventually cause the raceway to fatigue at the contact point.

    7. Passage of electric current through the bearing: In certain electrical machining applications, there is the possibility that an electrical current will pass through the bearing. A few possible causes would be stray magnetic fields or through a welding operation on some part of the machinery with the ground attached so that the circuit is required to pass through the bearings.

    8. Old age: Bearings are chosen during the initial design of a compressor based on “L10” life. L10 life is defined as the operating hours that 90 percent of a bearing population would be expected to meet or exceed before any wear surface develops a 1 mm square fatigue spall. The median life is approximately five times the L10 life. Good quality lubricant and a clean operating system can give operating service life well beyond the calculated L10 life. However, if compressors run long enough, the bearings would eventually be expected to fail from fatigue, or old age.

    Bearing Installation And Mounting

    To ensure that the correct bearings are being installed, it is recommended that bearings be obtained from the compressor manufacturer.

    Anti-friction bearings typically come in two mounting types, loose fit and interference fit. Loose fit bearings are designed to slide into the bore or over the shaft without resistance. Interference fit bearings require some assistance for installation.

    Four different mounting methods are used for anti-friction bearings, including cold mounting, hot mounting, oil injection, and slip fit. The most commonly used methods are cold mounting, hot mounting, and slip fit.

    Cold mounting takes place when a bearing is frozen prior to installation. Freezing shrinks the bearing allowing it to be easily installed in the bore. Once the temperature of the bearing increases, it fits snugly in the bore. Cold mounting is also used to describe a bearing that is mechanically forced into position. Hot mounting is used for bearings that require interference fit. A typical application would involve the inner race of an anti-friction roller bearing. Heating expands the race allowing it to be easily slid into position. As the race cools it adheres to the rotor shaft. Slip fit bearings simply slide into place with normal hand force.

    Yoder is a service technician with York Refrigeration/Frick in Waynesboro, Pa. For more information, visit www.yorkref.com.

    Publication date: 03/10/2003

  • Did you enjoy this article? Click here to subscribe to The NEWS Magazine

    You must login or register in order to post a comment.

    Hyderali Aluran
    April 27, 2013
    thanks and this is really usefull for me.if you prvide with more clear pictures of internal parts will be highly appreciated

    Multimedia

    Videos

    Image Galleries

    2014 MCAA Annual Convention

    Scenes from the 2014 MCAA Annual Convention in Scottsdale, Ariz.

    Podcasts

    NEWSmakers: Julian Scadden

    Training is an ongoing process. Julian will discuss how you can generate maximum return on time and energy invested training by following a three part process. Listen to this podcast to get expert tips on training, tracking and follow up. 

    More Podcasts

    THE MAGAZINE

    ACHRNEWS

    NEWS 04-14-14 cover

    2014 April 14

    Check out the weekly edition of The NEWS today!

    Table Of Contents Subscribe

    SERVICE CALLS POLL

    Which statement on service calls best applies to your business?
    View Results Poll Archive

    HVACR INDUSTRY STORE

    plumbing-hvac.gif
    2014 National Plumbing & HVAC Estimator

    Every plumbing and HVAC estimator can use the cost estimates in this practical manual!

    More Products

    Clear Seas Research

     

    Clear Seas ResearchWith access to over one million professionals and more than 60 industry-specific publications, Clear Seas Research offers relevant insights from those who know your industry best. Let us customize a market research solution that exceeds your marketing goals.

    DON'T MISS A THING

    Magazine image
     
    Register today for complete access to ACHRNews.com. Get full access to the latest features, Extra Edition, and more.

    STAY CONNECTED

    facebook icontwitter iconyoutube iconLinkedIn i con