Ice Breaker: Talking Oil Separators

October 5, 2009
/ Print / Reprints /
ShareMore
/ Text Size+

During the normal compression cycle, as the refrigerant is discharged from a compressor a small amount of refrigerant oil will also be discharged. It is important that this discharged oil returns back to the compressor. In order for the oil to return back to the compressor, good piping practices must be followed. If the refrigerant lines are not properly sized or configured, the oil may become trapped out in the system. If enough oil becomes trapped out in the system, the compressor could become starved for oil and bearing damage could occur.

An oil separator is an accessory used on some larger refrigeration systems to help limit the amount of oil in circulation. It is typically used on low temperature applications where the refrigerant’s mass flow rate is low. But it could be used on any system.

An oil separator will separate a major portion of the oil from the refrigerant as it is pumped from the compressor. It will also collect this separated oil and safely return it to the compressor’s crankcase. Oil separators are installed in the discharge line close to the compressor’s discharge. Sometimes they are heated and/or insulated to prevent the refrigerant inside from condensing at low ambient conditions.

As the refrigerant/oil mixture is discharged from the compressor, it enters the oil separator. The velocity of this mixture is slowed down from the use of internal baffles and impingement screens.

This slowing down causes a major portion of the oil to drop out of the mixture and fall to the bottom of the oil separator. At the bottom of the oil separator is a float assembly connected directly back to the crankcase of the compressor. As the oil level at the bottom of the oil separator increases, the float will cause a valve to open and, due to the pressure difference between the oil separator and the compressor’s crankcase, some of the oil will be returned to the crankcase until the float level in the oil separator drops and the valve closes.

While servicing systems with oil separators, one item to check is the temperature of the oil return line from the oil separator to the compressor. It should be just above room temperature most of the time. If it is hot all the time, this is an indication that the float assembly inside the oil separator may be stuck open and allowing hot discharge vapor to enter the compressor’s crankcase. This can lead to excessive crankcase pressures, overheating, and serious damage to the compressor.

Although oil separators can be quite efficient (some as high as 98 percent efficient), they do not separate all of the oil from the refrigerant. Some quantity of oil will always travel with the refrigerant throughout the system. They are not a cure for oil return problems. Good piping practices must always be followed while installing a system. Even with an oil separator, poor piping practices will eventually lead to oil being trapped out in the system causing a deficiency of oil in the compressor’s crankcase and possible compressor damage.

Publication date: 10/05/2009

Did you enjoy this article? Click here to subscribe to The NEWS Magazine

Recent Articles by Joe Marchese

You must login or register in order to post a comment.

Multimedia

Videos

Image Galleries

2014 Energy Efficiency Forum

Highlights from the 25th annual Energy Efficiency Forum in Washington, D.C.

Podcasts

NEWSMakers: Jeremy Begley

Jeremy Begley, home-performance specialist and Web and social media manager with National Heating and Air Conditioning Co. in Cincinnati discusses how and why you should add home-performance philosophies to your contracting repertoire. Posted on Sept. 12.

More Podcasts

ACHRNEWS

NEWS 09-15-14 cover

2014 September 15

Check out the weekly edition of The NEWS today!

Table Of Contents Subscribe

Venting R-22

The NEWS reported that a man received prison time for venting R-22. Should EPA step up enforcement?
View Results Poll Archive

HVACR INDUSTRY STORE

plumbing-hvac.gif
2014 National Plumbing & HVAC Estimator

Every plumbing and HVAC estimator can use the cost estimates in this practical manual!

More Products

Clear Seas Research

 

Clear Seas ResearchWith access to over one million professionals and more than 60 industry-specific publications, Clear Seas Research offers relevant insights from those who know your industry best. Let us customize a market research solution that exceeds your marketing goals.

DON'T MISS A THING

Magazine image
 
Register today for complete access to ACHRNews.com. Get full access to the latest features, Extra Edition, and more.

STAY CONNECTED

facebook icontwitter iconyoutube iconLinkedIn i con