Articles by Bill Johnson

Btu Buddy 101: Bob Trains Tim on His First Service Call

August 22, 2011
Bob and Tim have arrived at Tim’s first service call. Tim asked Bob, “What is this call all about?” Bob said, “This is a new customer that wants us to take over the maintenance work for this apartment house.”


Read More

Btu Buddy 100: Dual-Voltage, Nine-Lead Motors

July 18, 2011
Btu Buddy has met Bob for lunch to answer some questions that Bob had about yesterday’s service call. Bob asked, “Why did that motor have two contactors and so many wires going to it? It seemed very confusing. I am glad that I tagged those motor leads when I disconnected the motor. I never would have figured out how to reconnect the leads.”
Read More

Btu Buddy 99: Large Compressor Motor Grounded

June 20, 2011
Bob got a call to go to a convention center where the air conditioning system was not working. It was a 75-ton unit with one compressor. The system was many years old, but had been functioning fine, until now. After checking out the unit, an ohm check showed 0 resistance to ground.
Read More

Btu Buddy 98: Compressor With Internal Leak

May 23, 2011
Bob has received a call from the dispatcher about a system that is not cooling. The job is a small building with a 5-ton cooling unit. Bob went to the outdoor unit. It was running and all appeared normal. He went to the truck to get his gauges, and when he got back, he noticed that the compressor didn’t seem to be running.
Read More

Btu Buddy 97: Defective Compressor or Four-Way Valve Problem?

April 18, 2011
Bob has been sent on a service call where the customer is complaining about her power bill. She thinks that the heat pump may be the problem. Her power bill is much higher than last year. She explained this to Bob and he started by asking a question, “Does the auxiliary heat light come on very often on your thermostat?”
Read More

Btu Buddy 96: Motor and Circuit Protection

March 21, 2011
Bob and Btu Buddy were on a service call yesterday where the compressor motor was running overloaded due to internal load; the bearings were dragging or worn. Btu Buddy told Bob, “Motor overload protection and circuit protection are subjects that need to be discussed later.” They’ve gotten together today for that discussion.
Read More

Btu Buddy 95: Compressor Motor Overload

February 21, 2011
Bob got a call from the dispatcher to go to an office building that has a 3-ton heat pump compressor that has been shutting off after startup. The fan would continue to run. The building maintenance man said that he had observed the shutting down of the compressor several times.
Read More

Btu Buddy 94: A Heat Pump That's Not Getting Up to Temperature

January 24, 2011
Bob has gone on a service call where the customer is complaining that her house is not getting up to temperature. The house was heated with a heat pump with three stages of auxiliary strip heat. Bob removed the panel to the strip heat and found one of the units was not pulling current.
Read More

Btu Buddy 93: Pneumatic Controls Review

December 20, 2010
Bob and Btu Buddy have gotten together for a review of their last service call, which involved a control system that Bob was not very familiar with - pneumatic controls. Bob asked, “Why would anyone want to use air as the power source to operate the controls for a building?”
Read More

Btu Buddy 92: Pneumatic Control System

November 22, 2010
The customer’s complaint on this call was an overall overheating of his building. The manager told Bob, “We arrived this morning and the entire building was hot and keeps getting hotter.” He led Bob to the basement where there was a boiler. Bob found that the system had pneumatic controls.
Read More

Multimedia

Videos

Image Galleries

2014 MCAA Annual Convention

Scenes from the 2014 MCAA Annual Convention in Scottsdale, Ariz.

Podcasts

Kyle Gargaro, editor-in-chief of The NEWS, hosted the 2014 ACCA CEO Forum. At the event, six well-known, highly respected company executives, Gary Michel, Ingersoll Rand/Trane; Chris Nelson, Carrier Corp.; Chris Peel, Rheem Mfg. Co.; Rod Rushing, Johnson Controls; Brent Schroeder, Emerson Climate Technologies; and Doug Young, Lennox; provided individual industry outlooks and fielded questions directly from attending contractors. Listen to the entire event on the NEWSMakers podcast. Posted on April 14.

More Podcasts

THE MAGAZINE

ACHRNEWS

NEWS 04-14-14 cover

2014 April 14

Check out the weekly edition of The NEWS today!

Table Of Contents Subscribe

SERVICE CALLS POLL

Which statement on service calls best applies to your business?
View Results Poll Archive

HVACR INDUSTRY STORE

plumbing-hvac.gif
2014 National Plumbing & HVAC Estimator

Every plumbing and HVAC estimator can use the cost estimates in this practical manual!

More Products

Clear Seas Research

 

Clear Seas ResearchWith access to over one million professionals and more than 60 industry-specific publications, Clear Seas Research offers relevant insights from those who know your industry best. Let us customize a market research solution that exceeds your marketing goals.

DON'T MISS A THING

Magazine image
 
Register today for complete access to ACHRNews.com. Get full access to the latest features, Extra Edition, and more.

STAY CONNECTED

facebook icontwitter iconyoutube iconLinkedIn i con