Refrigeration

Ice Breaker: Taking an Oil Sample Without an Oil Plug

December 3, 2012
Trans

Checking the acidity and/or moisture content of refrigerant oil is one of the methods used to test if a refrigeration system is clean and uncontaminated. Many times this test is used after cleaning up a system from a compressor motor burnout, but it can be used anytime a system is suspected of being contaminated.

On compressors with an oil plug, taking this oil sample is no problem. Simply front seat the suction service valve and pump the compressor’s crankcase down to about 5 psig. Then electrically shut down the compressor and carefully loosen the compressor’s oil cap and allow the oil to seep around the cap and into a clean oil container. Do not take off the cap and allow the compressor crankcase to drop to atmospheric pressure.

If the compressor does not have an oil plug — like many hermetic compressors — taking an oil sample can be difficult. However, there is a solution if you think ahead and prepare for the need.

When the system is open to the atmosphere you can configure an oil trap. This will allow you to take an oil sample anytime you desire. The oil trap is simply an inverted tee with a Schrader valve placed in the suction line at least 6 pipe diameters downstream of any risers. An oil collector is then attached to the tee. The collector can be configured from a ½-inch sight glass with a shut-off valve on each end.

On one end add a ¼-inch female fitting with a Schrader depressor to the shut-off valve and on the other end a ¼-inch cap to its shut-off valve. Attach the collector to the tee while the system is open to the atmosphere. Open the shut-off valve connected to the tee and close the shut-off valve with the capped end. This will allow the collector to be exposed to system while the system is being evacuated and charge with refrigerant.

As the system runs and the refrigerant returns to the compressor, some of the oil will fall to the bottom of the collector. Monitor the process and when enough oil has been trapped, isolate the collector from the system using the shut-off valve and remove it from the tee. Place a ¼-inch cap on the Schrader valve when done to prevent damage to its threads and prevent any refrigerant loss, if the Schrader core were to leak.

If another oil sample is needed, simply place the collector back on the inverted tee with both shut valves initially closed. On the collector’s capped end, remove the cap and connect a vacuum pump to fitting, open the shut-off valve, and pull a vacuum on the collector. When done, close the valve and turn off the vacuum pump, then open the valve to the system and collect some more oil.

This method does require some extra time and materials on a job, but it will allow you to take an oil sample from a system without an oil plug.

Publication date: 12/3/2012
 

Did you enjoy this article? Click here to subscribe to The NEWS Magazine

Recent Articles by Joe Marchese

You must login or register in order to post a comment.

Multimedia

Videos

Image Galleries

2014 Energy Efficiency Forum

Highlights from the 25th annual Energy Efficiency Forum in Washington, D.C.

Podcasts

NEWSMakers: Jason Vogelbaugh

Jason Vogelbaugh of Alpha Controls drops in to the NEWSMakers podcast to discuss his role with the company, the InsideIQ Building Automation Alliance, and current energy-efficiency projects being worked on. Posted on Sept. 26.

More Podcasts

ACHRNEWS

NEWS 09-29-14 cover

2014 September 29

Check out the weekly edition of The NEWS today!

Table Of Contents Subscribe

Venting R-22

The NEWS reported that a man received prison time for venting R-22. Should EPA step up enforcement?
View Results Poll Archive

HVACR INDUSTRY STORE

plumbing-hvac.gif
2014 National Plumbing & HVAC Estimator

Every plumbing and HVAC estimator can use the cost estimates in this practical manual!

More Products

Clear Seas Research

 

Clear Seas ResearchWith access to over one million professionals and more than 60 industry-specific publications, Clear Seas Research offers relevant insights from those who know your industry best. Let us customize a market research solution that exceeds your marketing goals.

DON'T MISS A THING

Magazine image
 
Register today for complete access to ACHRNews.com. Get full access to the latest features, Extra Edition, and more.

STAY CONNECTED

facebook icontwitter iconyoutube iconLinkedIn i con